MB-TTXL Tool Tote Rubber BaseVPP10033
Rated 5.00 out of 5 based on 4 customer ratings
(4 customer reviews)


A Wider Full Featured Open Tool Tote

Out of stock

Join the waitlist to be emailed when this product becomes available

Add to Compare


The MB-TTXL is a wider version of the MB-TT tool tote, with a non-marking rubber bottom, is designed for Builders, General Contractors or any tradesman or technician to store hand tools on the inside pockets and bulk storage capacity in the middle. This tool organizer is also designed to accommodate Boat Builders and Shipwrights to store, carry and access all of their tools.



  • Height: 13" (33cm)
  • Width: 16.5" (42cm)
  • Depth: 9” (23cm)
  • Weight (empty): 7.5lbs (3.5kg)
  • Max Payload: 45lbs (20kg)
  • Internal Volume: 1870in3 (30.5L)


  • 2 Interior, Removable Pocket Panel Sleeves, Totaling 20 Pockets
  • 32 Exterior Vertical Tool Pockets
  • Polypropylene bottom over-molded with non-marking TPR Rubber
  • Stainless Steel Tape Measure Clip


  • Polyester Canvas Body Fabric
  • Leather Grips and Trim


  • Warranty: 5 Years (see Veto warranty terms and conditions)

Download MB-TTXL Product Sheet

Additional Information


Keep the Zippers Clean & Lubricated

Over time, dirt and grit will “clog” the zipper coils preventing them from staying closed. To keep this from happening, clean and lubricate your zippers twice a year (more often if you work on a job site with a high amount of airborne debris). To clean the coils: Scrub them with soapy water; a tooth brush works very well. After scrubbing the coils, blow them out with an air hose to dislodge any other fine grit that didn’t dislodge with the brush. To lubricate the coils: Apply a silicone spray, beeswax or a zipper lubricant.

Protect the Zippers From Sharp Objects and/or Excessive Heat

Any sharp object or heat source is capable of permanently damaging the zippers. Once a zipper coil is cut or singed the zipper will not function and in most cases is not repairable. Most of the cut zipper coils we see are the result of sharp tools stored inside the bag with the sharp side facing up. Make sure to keep the sharp edges of your tools facing down in your bag and away from the zipper coils.

Don’t Overstuff the Bag

Overstuffing your tool bag will very likely cause significant stress on the zippers that is above and beyond what the bag was built for and will eventually cause the zipper(s) to separate. If you have to work hard to close your zipper(s), your tool bag is most likely overstuffed… proceed with caution!

Download The Product Sheet of MB-TTXL

Video & Product Sell Sheet

4 reviews for MB-TTXL Tool Tote Rubber Base

  1. Rated 5 out of 5

    Keifer (verified owner)

    This thing is a beast. Very solid construction with plenty of holders for tools, etc. I plan to pass it on to one of my kids.Yep. I have that kind of faith it will last that long and become an heirloom.

  2. Rated 5 out of 5

    Jennifer Duarte (verified owner)

    Bag is made with extremely great quality. There is plenty of room for all my tools, and more. Excited to use it for many years to come.

  3. Rated 5 out of 5


    It’s the annual spring promotion again. I wanted to buy the DRXL, but it was out of stock. I saw this TTXL later, and it was much better than expected.

  4. Rated 5 out of 5

    Walter S.

    As soon as I saw this bag I knew it was going to be my new duct bag. After loading it up it achieved exactly what I needed. All snips have their own pocket as well as tongs and specialty tools. Large center area for Andy’s and folding bar. Good wide pockets on the outside for my metal hole punch and one side hard plastic perfect for an unsheathed duct knife. This bag will give many years of quality service.

Add a review