DH1 Drill HolsterVPP10515

From $109.99

Handmade in New England (USA), the DH1 Small Drill Holster brings additional features to a drill holster. The exterior sides of the DH1 integrate 4 small pockets perfect for 2-4” bits, extensions, and/or nut drivers. A horizontal strip of webbing along the top provides an easy-to-reach perch for short driver tips as well as storing the safety lanyard clip while working at ground level. A slot behind the front panel is a handy location to clip a tape measure. The DH1 offers two options for attaching itself to a belt or tool bag: a belt pass-through or the option to add our stainless steel Repositionable Belt Clip (RBC – sold separately) to the vertical molle on the rear.

In stock

- +
Add to Compare

Description

Handmade in New England (USA), the DH1 Small Drill Holster brings additional features to a drill holster. The exterior sides of the DH1 integrate 4 small pockets perfect for 2-4” bits, extensions, and/or nut drivers. A horizontal strip of webbing along the top provides an easy-to-reach perch for short driver tips as well as storing the safety lanyard clip while working at ground level. A slot behind the front panel is a handy location to clip a tape measure. The DH1 offers two options for attaching itself to a belt or tool bag: a belt pass-through or the option to add our stainless steel Repositionable Belt Clip (RBC – sold separately) to the vertical molle on the rear.

Specification

PRODUCT SPECIFICATIONS:

  • Height: 9" (23 cm)
  • Width: 6" (15 cm)
  • Depth: 3"  (7.5 cm)
  • Weight (empty):  0.5 lbs/0.2 kg
  • Max Payload: 7.5 lbs/3.5 kg

MAXIMIZED TOOL STORAGE CAPACITY:

  • Made in USA
  • Rugged construction & aluminum hardware
  • Belt Pass-through
  • Bottom flap closes to protect chuck / opens for long bit clearance
  • 4 External pockets for bits, extensions, and nut drivers
  • 4 1” Bit holders
  • Safety lanyard
  • Tape measure clip
  • Optional Repositionable Belt Clip (RBC) – sold separately

OTHER FEATURES:

  • Warranty: 5 Years (see Veto warranty terms and conditions)

Additional Information

Veto Pro Pac Tool Bags Product Care and Maintenance

Keep the Zippers Clean & Lubricated

Over time, dirt and grit will “clog” the zipper coils preventing them from staying closed. To keep this from happening, clean and lubricate your zippers twice a year (more often if you work on a job site with a high amount of airborne debris). To clean the coils: Scrub them with soapy water; a tooth brush works very well. After scrubbing the coils, blow them out with an air hose to dislodge any other fine grit that didn’t dislodge with the brush. To lubricate the coils: Apply a silicone spray, beeswax or a zipper lubricant.

Protect the Zippers From Sharp Objects and/or Excessive Heat

Any sharp object or heat source is capable of permanently damaging the zippers. Once a zipper coil is cut or singed the zipper will not function and in most cases is not repairable. Most of the cut zipper coils we see are the result of sharp tools stored inside the bag with the sharp side facing up. Make sure to keep the sharp edges of your tools facing down in your bag and away from the zipper coils.

Don’t Overstuff the Bag

Overstuffing your tool bag will very likely cause significant stress on the zippers that is above and beyond what the bag was built for and will eventually cause the zipper(s) to separate. If you have to work hard to close your zipper(s), your tool bag is most likely overstuffed…proceed with caution!

Download The Product Sheet of

Video & Product Sell Sheet

Reviews

There are no reviews yet.

Be the first to review “DH1 Drill Holster”